Digital Printing Knowledge
Digital

Digital proofs are made directly from the computer authored digital file without creating a set of films. The digital file is the same file that will be used to create the printing plates. The quality of digital proofs has improved to a level that is acceptable for use as a contract proof, which is necessary as the industry moves to a filmless workflow. Further improvements involve proofing systems that create proofs containing halftone dots, which gives a more accurate representation of the image to be reproduced.

When using digital systems for proofing, be aware that the device(s) need to be color calibrated often to maintain color accuracy, and color bars should be used on every proof.

A digital proofing process involves printing each of the subtractive primary color components of the image (cyan, magenta, yellow), and black on one pass through the output device to create the full color digital proof as shown below.

Different types of digital color printers are:

 
Digital Sublimation

A digital sublimation proof is the closest of all digital proofers to the analog proofing method. Like the analog method, the transparent colorant is transferred from a sheet or roll (called ribbons) of clear polyester base, which has been coated with the colorant. The ribbons are brought into contact with a receiver sheet and varying temperatures of heat are used to transfer the colored material in the image area to the receiver. The colorant begins as a solid and then it is heated to become a gas. Once the colorant is on the receiver, it cools and becomes a solid again. This procedure is completed for each color. Most systems can transfer the colorant to the actual printing stock either directly or as an additional step. The digital sublimation proof system requires little maintenance and is reasonably consistent.

There are two different types of sublimation proofers, dye sub and laser sub. The dye sub uses dyes to create the color on the proof and the heat required in the proofing process is supplied by a thin pointed metal stylus. The laser sub uses pigments to create the color on the proof and a laser is used to provide the heat that is required.

Dye Sublimation Proofers were the first of the sublimation systems on the market. The proofs are called Dye Subs. They utilize a series of thousands of styluses and dye based colorants, which are relatively inexpensive and reasonably fast. The disadvantages are: the dye colors on the proof will fade with time and may not match the color at the press; the proofs must be viewed under proper lighting conditions; the process has limited resolution and produces a continuous tone effect.

Laser Sublimation Proofers are the first of the dot oriented digital proofers. This system is much more expensive and is slower than the dye sub system, but the quality has been considered equal to the analog proofing system. The laser sublimation proof system has been optimized for dot resolution and dye match to the point where it is currently the standard. The disadvantages of this system are that the proofs can also change color over time and they must be viewed under proper lighting conditions.

Thermal Wax

Thermal wax printers work the same way as the dye-sub printers except the printer ribbon is coated with colored wax instead of using dyes. As the thermal head heats up, the wax fuses to the paper. The thermal wax printer also prints only one process color at a time so the paper must be fed into the printer four separate times to produce the full color image. Thermal was printers produce a stronger color than the ink jets, and they are much faster, but they are also move expensive.

Inkjet

Inkjet printers range from inexpensive desktop units suitable for letter size paper to floor units capable of printing banners that are 36" wide and several feet long. The ink comes in bottles containing the process colors and is sprayed from nozzles onto the paper. Instead of printing a single row of pixels, the ink jet printer prints a series of rows, vertically, each time it travels across the sheet. 

Some systems use six-colors to get 'photographic-quality' output. The six-color inkjet printer add light cyan and light magenta inks which produce more subtle flesh tones and finer color gradations than the standard four colors.

There are several types of inkjet technology, but the most common are drop on demand (DOD) and continuous flow. DOD works by squirting small droplets of ink onto the paper. A continuous flow system works with a continuous flow of very small droplets of ink directed toward a receptor base mounted on a spinning drum. In locations where color is not needed, the droplets are deflected and captured by a waste collection system.

Since the proofing substrate is much whiter and glossier than most papers, the proofs usually appear better than the printed piece. To compensate for the paper difference, some inkjet systems allow a simulation of the paper to be printed on the proof, by printing the paper color with the rest of the document. Also, some printers allow you to use the same paper that will be used for printing the job on the press. This method of color management is called absolute colorimetric rendering.

The inkjet printers require high-quality coated or glossy paper for the production of photorealistic output. The special paper that is required is composed of two layers. The base layer is paper, and the second layer is a coating which accepts inkjet ink. The surface must allow the ink to dry instantly during printing to avoid smearing and ink spreading. The weight of the paper must be heavy enough to avoid bleed through and curling, but of a weight that can be folded and handled like regular printing stock.

The problems associated with inkjet printers are:

  • The ink has a tendency to smudge immediately after printing.
  • The proofs are not waterproof.
  • They are expensive to maintain. The special coated paper required to produce high-quality output is very expensive, and the ink cartridges which can also be expensive need be changed often. Most systems have one cartridge for the black ink and one cartridge for the other three colors (cyan, magenta, and yellow). If one of the three colors runs out before the other two, the entire cartridge must be replaced.

Color Laser Printer

Laser printers and copiers use a pre-charged drum or belt that conducts a charge when exposed to light. Toner is magnetically attracted to the appropriate areas of the image and repelled from others. The printer transfers the image to the paper where it is fused by heat and pressure.

Color laser copiers, interfaced with fast and powerful RIPs, are now being used by service bureaus, quick printers, and design shops as a way of producing quick proofs or short-run, variable-data digital color printing.

Laser Thermal Imaging Proofer

The thermal proofer is a high-end halftone digital proofer that uses pigment based colors to produce exceptionally high quality proofs. This is the fastest growing type of proofer because it gives the closest match to the actual printing process. It is driven by a single RIP that is also used to produce press plates.

The substrate is attached to a drum and a donor sheet (ink sheet) is attached on the top of the substrate. An infrared diode laser beam strikes the donor sheet and the material is transferred from the colored donor sheet to the substrate. Since the same RIP and laser exposure unit that creates the proof also creates the printing plate, the proof reflects the same dot structure and angles of the printed press sheet.

The following are factors to consider when using digital proofs:

  • Dots or no dots - many of the technologies cannot produce proofs with halftone dots. The systems that are able to produce proofs with halftone dots, may not produce dots that are the exact size and shape, or at the same screen angle as those imaged on the printing plate. With the differences in dot size and shape and screen angles, it would be difficult to predict problems such as moiré patterns.
  • Another factor is the ability to see the effects of overprinting.
  • The key advantages of digital proofs over analog proofs are that the costs can be less than half that of an analog color proof and they are produced in much less time.

Tips for checking a digital proof for accuracy

 


Back to Top

 

More Proofing >>

Additional search results for:
   Digital
knowledge
Digital Copiers
Digital Desktop Printers
Digital Presses
Remote Digital
Digital Image Sensor
glossary
Personal Digital Assistant (PDA)
Integrated Services Digital Network (ISDN)
Direct Digital Color Proof (DDCP)
Digital Signature
Digital Proof
Digital Printing
Digital Press
Digital Plates
Digital Photography
Digital Papers
Digital Job Ticket
Search
Enter keywords to search
PrintingTips.Com Knowledge
Print Preparation
Bar Coding
Finishing
Materials
PDF
Postal
Prepress
Analog Platemaking
Color
Desktop Publishing
Imaging
Planning and Design
Proofing
Analog
Analog Proofing Tips
Color Matching
Color Viewing Booth
Contract
Digital
Galley
Laser
Press
Remote Digital
Scatter
Soft
Specifications
Spot Color
Software
Print Processes
Security Features
Tools
Print Products
RelatedContent
knowledge
glossary
Features of Interest
Featured Ad
Terms of Use |  Privacy Policy |  Site Map |  Index |  Contact Us
Reproduction in whole or in part without written permission is strictly prohibited.
© Copyright 2024 Tecstra Systems, All Rights Reserved, PrintingTips.Com

Digital - PrintingTips.com

Printing Tips Home Customer Service Knowledge Glossary Printing Tips Home